Waldorf Q+ User Manual Page 149
- Page / 171
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
MIDI Control – Channel Based MIDI Messages
Waldorf Q User’s Manual 150
Pitchbend Messages
The Q sends and receives Pitchbend Messages with a resolution of 14 bit. The pitchbend ranges are
controlled by the Bend Range parameter in the Oscillator Edit menus. Pitchbend Messages can also
be used as “Pitchbend” modulation source.
Modulation Wheel
The Q sends Modulation Wheel changes as Modulation Wheel MSB Message (Controller #1).
Modulation Wheel LSB (Controller #33) is not sent when the Modulation Wheel is turned but used to
change a particular sound parameter as you can read in the chapter “Influencing / Editing Sounds
over MIDI” on page 151.
The Q receives Modulation Wheel MSB Messages and evaluates them as “Modwheel” resp. “MW”
modulation source.
Breath Control Messages
The Q receives Breath Control MSB Messages and evaluates them as “BreathCtr” modulation source.
Foot Controller Messages
The Q receives Breath Control MSB Messages and evaluates them as “Foot Ctr” modulation source.
Channel Volume Messages
The Q receives Channel Volume Messages (Controller #7) and scales the output of the respective
Sound to that value. The maximum Sound volume depends on the settings in the Sound, Instrument
and Multi, Channel Volume changes the volume relatively to these settings.
Pan Messages
The Q receives Pan Messages (Controller #10) and balances the two Filter outputs by that value. A
value of 64 means that the Filter Pan settings are kept as they are while smaller values weigh the
signal to the left output and bigger values weigh the signal to the right output.
Sustain Pedal Messages
The Q receives Sustain Pedal Messages (Controller #64) and evaluates them as follows: if a value
greater or equal than 64 is received, the “Key Pressed” envelope phases of all voices of the respective
MIDI channel are played. If a value smaller than 64 is received, the “Key Off” envelope phases are
played. Sustain Pedal Messages can also be used with the “Sust. Ctr” modulation source.
Sostenuto Pedal Messages
The Q receives Sostenuto Pedal Messages (Controller #65) and evaluates them as follows: if a value
greater or equal than 64 is received, the “Key Pressed” envelope phases of the currently playing
voices of the respective MIDI channel are played. Voices that are played afterwards are not affected
by the Sostenuto Pedal message. If a value smaller than 64 is received, the “Key Off” envelope phases
of the affected voices are played.
Footswitches
The Footswitches send value 0 (off) and 127 (on) on the controller numbers they are set to in the
Global menu. There is no dedicated “MIDI Footswitch Message” so the reception of the MIDI
Messages they originally generated depends on the settings of the parameters of the current Sound.
- User´s Manual 1
- Q Keyboard/Q Rack/Q+ 1
- Garantiekarte / Warranty Card 2
- Foreword 4
- Front Panel Q Keyboard 5
- Frontpanel Q Rack 6
- Rear Panel 7
- Contents 8
- Introduction 10
- What to read? 11
- General Safety Guidelines 14
- Proper Use 15
- Setup and Connection 16
- ☞ To connect the devices: 17
- Audio Connections 18
- Digital S/PDIF Output 18
- External Input 19
- Switch Pedal Inputs 19
- Overview 20
- Memory Card 21
- Basic Operation 22
- Panic Function 23
- System Volume 23
- Demo Playback 23
- The Master Section 24
- Selecting Programs 24
- Multi Mode 25
- 78654321 90 26
- Bank Hold 27
- Switching Banks 27
- ☞ To select a card program: 28
- ☞ To select one instrument: 29
- Editing Parameters 30
- Editing Panel Parameters 31
- Control and Button Types 32
- ☞ To store a program: 35
- Instrument settings 38
- Volume 000…127 39
- Channel global, omni, 1…16 39
- LowKey C-2…G8 43
- HighKey C-2…G8 43
- Pattern off, 001…100 43
- Multi settings 44
- Multi Mixer 44
- Multi Tempo 40…300 45
- Step Sequencer 46
- Deselecting all Steps 47
- Programming Notes or Chords 47
- Programming a Pause 47
- ☞ To program a Hold event: 48
- Sequencer Panel Controls 49
- Sequencer Rotaries 50
- Sequencer Edit Menu 50
- Selection of a Pattern 51
- Option Line Parameter 51
- Pattern Length 1…32 52
- Transpose Key C-2…G8 52
- Rotate Steps 53
- Sound Parameters 54
- The Tempo 55
- Modulation Speed Levels 56
- Fast Modulation 57
- Standard Modulation 58
- Xphorm Edit Menu 62
- Triggering of Voices 63
- Oscillators 65
- The Sawtooth Wave 66
- The Square Wave 67
- The Pulse Wave 68
- The Triangle Wave 69
- Wavetable Synthesis 70
- Oscillators Panel Controls 71
- Detune -64…+63 72
- FM 0…127 72
- Pulsewidth 0…127 73
- PWM -64…+63 74
- Alt1 and Alt2 waveforms 75
- Sync Osc2 / Sync off / on 75
- PitchMod -64…+63 76
- Oscillators Edit Menu 77
- Glide Rate 0…127 78
- Glide / Active off / on 78
- Mixer Panel Controls 79
- Osc2 0…127 80
- Osc2 Balance F1 64…mid…F2 63 80
- Osc3 0…127 80
- Osc3 Balance F1 64…mid…F2 63 80
- RingMod 0…127 80
- Mixer Edit Menu 81
- Frequency 84
- Resonance 84
- Selecting and Editing Filters 85
- Filter Panel Controls 86
- Velo -64…+63 87
- Pan left 64…center…right 63 87
- Drive 0…127 87
- Filter Edit Menu 88
- Filter Types 89
- 24dB Notch and 12dB Notch 90
- The Comb filter as Chorus 92
- The Comb filter as Flanger 93
- 12dB/24dB Analog LP (Q+ only) 94
- Env Velo 95
- Amplifer Edit Menu 96
- Effect Panel Controls 97
- FX1 and FX2 Edit Menus 97
- Speed 0…127 98
- Depth 0…127 98
- Delay 0…127 98
- Overdrive 101
- Cutoff 0…127 102
- Overdrive 0…127 102
- Ring Mod 0…127 102
- Tap Delay 105
- 5.1 Delay 106
- 5.1 Surround Delay Types 106
- 5.1 D.Clk 108
- ☞ Building a Vocoder setup 109
- Bands 002…025 110
- S. Offset -64…+63 110
- Hi Offset -64…+63 110
- Arpeggiator 112
- Length 1/192…1/1 / legato 113
- Range 1 Oct…10 Oct 113
- Arpeggiator Edit Menu 114
- Max. Notes 1…16 115
- Clock 1/32t…1/1 115
- Length 1/192…127/192 / legato 115
- T. Factor 0…127 116
- Same Note Overlap Off / On 116
- Arp Timing ˆ / ¯…˛ 119
- Arp Steplen ˜ / ¯…˛ 120
- Envelopes 121
- ADSR Envelope 122
- ADS1DS2R Envelope 123
- One Shot 124
- Loop S1S2 125
- Loop All 126
- Shape Sync 127
- Speed Delay 127
- Shape Sync Speed Delay 127
- LFO Edit Menu 128
- Fade out 64…in 63 129
- Clocked Off / On 129
- Phase free, 000°…357° 129
- Modulation Matrix 130
- Modifier Matrix 131
- Control Delay 132
- Drum Map 133
- Key C-2…G8 134
- Transpose -60…+60 134
- Volume 0…127 134
- Global Parameters 135
- Tuning 430…450 Hz 137
- Transpose -12…+12 137
- HMT depth 000%...100% 138
- HMT MIDI Export off / on 138
- Ctrl W…Ctrl Z 0…120 139
- Input Gain 1…4 142
- Mix Level 0...127 143
- Operating System (OS) 143
- Pedal/CV1 Offset -64…+63 143
- ☞ To adjust Pedal/CV 1 Gain: 144
- Pedal/CV2 Gain 0...127 145
- Pedal/CV2 Curve 0...127 145
- Utility menu 146
- Init Drums 147
- Random Sound 147
- Rename Card 147
- MIDI Control 148
- Sending System Exclusive Data 151
- Other Functions 153
- The HMT function 155
- Tips & Tricks 156
- Appendix 157
- MIDI Signalflow Diagram 159
- Glossary 160
- Controller Numbers 164
- MIDI Implementation Chart 168
- Waldorf Q User’s Manual 170 169
- FCC Information (U.S.A.) 170
Related products and manuals for Synthesizer Waldorf Q+
Synthesizer Waldorf zarenbourg User Manual
(22 pages)
(22 pages)
Synthesizer Waldorf Pulse Plus User Manual
(80 pages)
(80 pages)
Synthesizer Waldorf PPG Wave 2.V User Manual
(82 pages)
(82 pages)
Synthesizer Waldorf MicroWave XT User Manual
(126 pages)
(126 pages)
Synthesizer Waldorf MicroWave XT User Manual
(19 pages)
(19 pages)
Synthesizer Waldorf Pulse User Manual
(78 pages)
(78 pages)
Synthesizer Waldorf XTk User Manual
(132 pages)
(132 pages)
Synthesizer Waldorf Pulse User Manual
(11 pages)
(11 pages)
Synthesizer Waldorf Pulse User Manual
(19 pages)
(19 pages)
Synthesizer Waldorf Pulse User Manual
(9 pages)
(9 pages)
© 2020, manymanuals.com. All rights reserved. | 1.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals