Waldorf MicroWave XT User Manual Page 45
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Limit
off / on
This setting prevents, if enabled, accessing the analog type waveforms triangle, square and
sawtooth in any case of modulation. When disabled, the full modulation amount will be
calculated and applied so that the whole wavetable will be used for tone generation.
Wave 2
Wave 2 / 1
Wave 2 / 2
Startwave
00...60 / triangle / square / sawtooth
Determines the start point of the wavetable that is used when the sound starts. As an
alternative to the waves of the currently selected wavetable, you can select the basic
waveforms
triangle
,
square
with 50% duty cycle or
sawtooth
.
When you want to create a sound with a wave sweep, you should roughly set the Startwave
parameter onto the desired wave, before you apply any modulations to the corresponding
Wave module. This helps you to find the basic waveform where all modulations start from.
Note that you can apply unipolar and bipolar modulation sources to the Wave module as
with any other module. For example, set the Startwave parameter to
29
, which is almost the
middle of the wavetable and apply a slow running LFO to the Wave module to sweep
through the whole wavetable (except the three waveforms triangle, square or sawtooth). Try
it with one of the PWM wavetables.
The basic waveforms triangle, pulse and sawtooth correspond to entry
61…63
of
each wavetable. Please notice, that these waveforms are also used when an
appropriate wave modulation is applied. To avoid this, you will have to activate the
Limit parameter. Please read this corresponding topic to get further information. Use
the basic waveforms to generate traditional, analog synthesizer sounds.
Phase
free / 3...357°
By means of this parameter you can define the startsample and, as a result, the phase of the
generated wave. Alternative to a fixed value, you can use
free
to set the phase to a different,
random value each time a note is generated. The setting is scaled in degrees.
Link
off / on
Allows the use of the same modulation settings for both waves. When enabled, wave 2 uses
the modulation parameters of wave 1 for all Modulation Matrix settings, EnvAmount,
EnvVelAmt and Keytrack. That means, whenever a modulation is applied to wave 1, it is
also used for wave 2. When disabled, each wave uses its own individual modulation
settings.
EnvAmount
-64…+63
Determines the amount of influence the wave envelope has on the wavetable modulation.
EnvAmount|EnvVelAmt|Keytrack |Limit W2
-20 | +15 | +050% | off
Startwave| Phase | Link W2
057 | free | off
User’s Manual MicroWave II • MicroWave XT • XTk
45
- Bedienungsanleitung 1
- User's Manual 1
- Garantiekarte / Warranty Card 3
- Contents 5
- Diagrams 6
- Front Panel 7
- Rear Panel 7
- Foreword 10
- -2 11
- General Safety Guidelines 12
- Maintenance 13
- Proper Use 13
- Inventory 14
- Connections 14
- Analog Input 15
- Quick Start 16
- Saw Repeat WMF 16
- 01 16
- Store Sound A001 A001 ? 17
- Saw Repeat WMF 17
- 092 17
- Multi Mode 20
- Activating the Instrument 21
- Building a layered Sound 22
- Operation 23
- Editing Parameters 25
- Saw repeat WMF 26
- -1 26
- Edit Buffers 27
- The Compare Function 27
- Recalling Edits 28
- Storing Programs 28
- The Play Access Page 29
- Panic Function 30
- Randomizing a Program 30
- Initializing Programs 30
- Init Multi 31
- About Wavetable Synthesis 33
- Overview 34
- Wavetable 35
- What else can we do? 36
- Creating own Wavetables 37
- Overview of Functions 38
- Oscillators 39
- Oscillator 2 40
- Oscillator 1 42
- Oscillator 2 in Sync 42
- 001...128 43
- 065…128 43
- 065…096 43
- Wave 2 / 1 45
- Wave 2 / 2 45
- 3 47
- External 48
- 113 48
- Play Access 49
- Example 1 50
- Example 2 50
- Example 3 50
- Example 4 50
- Frequency 51
- Resonance 51
- Filter 1 52
- Filter Types 53
- 12db High Pass 54
- Filter 1 / 2 55
- 24dB Notch Filter 56
- 12dB Notch Filter 56
- Bandstop Filter 56
- Filter 2 56
- -200%…+197% 57
- Amplifier 58
- 090 58
- Panning 59
- Effect 60
- Chorus 60
- MicroWave II MicroWave XT 60
- Flanger 1 61
- Flanger 2 61
- AutoWahLP 61
- AutoWahBP 62
- Overdrive 62
- Amp. Mod 63
- Pan Delay 63
- Effect 64
- Mod Delay 64
- Active 65
- Trigger 1 66
- Trigger 2 66
- Arpeggiator 68
- Position 71
- 03 71
- Arpeggiator User Pattern 71
- Filter Env 72
- 000 72
- Amplifier Env 73
- Wave Envelope 74
- Free Envelope 77
- LFO 1 / 1 78
- LFO 1 / 2 78
- LFO 2 / 1 79
- LFO 2 / 2 79
- Modifier Delay 81
- Modifier Units 82
- Mod 1…16 85
- Modwheel 85
- Program Name 86
- Multi parameters 87
- Instrument parameters 88
- Key Velocity 95
- Velocity 95
- MIDI Control 97
- Sending System Exclusive Data 98
- Updating the System Software 100
- Converting MicroWave Sounds 101
- Appendix 102
- Software release 2.28 103
- System Exclusive Data Format 106
- Glossary 117
- MIDI Implementation Chart 122
- FCC Information (U.S.A.) 124
Related products and manuals for Synthesizer Waldorf MicroWave XT
Synthesizer Waldorf MicroWave XT User Manual
(19 pages)
(19 pages)
Synthesizer Waldorf Pulse User Manual
(78 pages)
(78 pages)
Synthesizer Waldorf XTk User Manual
(132 pages)
(132 pages)
Synthesizer Waldorf Pulse User Manual
(11 pages)
(11 pages)
Synthesizer Waldorf Pulse User Manual
(19 pages)
(19 pages)
Synthesizer Waldorf Pulse User Manual
(9 pages)
(9 pages)
© 2020, manymanuals.com. All rights reserved. | 1.994 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals